HOT ! New Look｜Natural Look Paver Sealer｜ Other Products

Plus SAND LOCK for Interlocking Pavers and Bricks
Seals pavers and bricks & locks in sand joints in one easy coat. Excellent resistance to stains, efflorescence, weeds, and UV fading. Natural low gloss is easy to maintain.

No Gloss, Easy to Apply
Slight Color Enhancement
Low Maintenance
Resists Oil, Grease
Resists Weeds & Mildew
Resists Color Fading

Surface Preparation: Prior to the application of Glaze ‘N Seal products, surface must be thoroughly clean and dry. Remove all dirt, oil, grease, paint, efflorescence and surface sealers. General cleaning may be done using Glaze ‘N Seal Heavy Duty Cleaner for Concrete and Masonry. For efflorescence stains use Glaze ‘N Seal Efflorescence Remover. When acid has been used for any reason, surface must be neutralized. We recommend Glaze ‘N Seal Neutralizing Rinse. Read product container for specific instructions and cautions with any cleaner. Never mix cleaners. Allow at least 24 hours of drying time before sealing (48 hours if power washing has been done or if temperature is cool). New concrete pavers should cure 14 days or more before sealing. Applying sealer to a damp or incompletely cured surface may cause a hazy appearance or loss of adhesion.
After tamping down the joint sand and sweeping the application area clean be sure the sand (regular or polymeric) is at least 1/8 inch below the surface of the pavers. The sand should be dry to its full depth before sealing for best results.
Note: Before applying Glaze ‘N Seal products to the entire surface, test several small areas to verify the product’s appearance, penetration and protective ability.
Application Procedure: Use garden-type sprayer, low pressure airless sprayer, brush, short nap roller or squeegee for application. Apply one coat in liberal saturating manner to ensure that joints are flooded. (If sand is being sealed use a squeegee, not a roller, to remove excess sealer and avoid puddling). Allow additional drying time in moist, cool climates. An optional second coat may be applied after two hours if desired to increase protection and gloss. Recoat as needed. For added slip resistance Glaze’ N Seal Grip ‘n Seal Slip Resistance Additive may be added to the second coat of sealer.
Coverage: 75 to 150 square feet per gallon depending on porosity of surface and method of application.

Product Uses: Seals pavers and bricks & locks in sand joints in one easy coat. Excellent resistance to stains, efflorescence, weeds, and UV fading. Natural low-gloss finish is easy to maintain.
Special Features:
• Reduces efflorescence • Reduces freeze thaw effects • Resists oil, grease rust stains • Locks sand between joints• Non-flammable • Re-coatable• Cleans up with water • Resists weed growth • Low VOC • LEED eligible
DO NOT SHAKE — DO NOT ALLOW TO FREEZE
Surface Preparation: Prior to the application of Glaze ‘N Seal products, surface must be thoroughly clean and dry. Remove all dirt, oil, grease, paint, efflorescence and surface sealers. General cleaning may be done using Glaze ‘N Seal Heavy Duty Cleaner for Concrete and Masonry. For efflorescence stains use Glaze ‘N Seal Efflorescence Remover. When acid has been used for any reason, surface must be neutralized. We recommend Glaze ‘N Seal Neutralizing Rinse. Read product container for specific instructions and cautions with any cleaner. Never mix cleaners. Allow at least 24 hours of drying time before sealing (48 hours if power washing has been done or if temperature is cool). New concrete pavers should cure 14 days or more before sealing. Applying sealer to a damp or incompletely cured surface may cause a hazy appearance or loss of adhesion.
After tamping down the joint sand and sweeping the application area clean be sure the sand (regular or polymeric) is at least 1/8 inch below the surface of the pavers. The sand should be dry to its full depth before sealing for best results.
Note: Before applying Glaze ‘N Seal products to the entire surface, test several small areas to verify the product’s appearance, penetration and protective ability.
Application Procedure: Use garden-type sprayer, low pressure airless sprayer, brush, short nap roller or squeegee for application. Apply one coat in liberal saturating manner to ensure that joints are ooded. (If sand is being sealed use a squeegee, not a roller, to remove excess sealer and avoid puddling). Allow additional drying time in moist, cool climates. An optional second coat may be applied after two hours if desired to increase protection and gloss. Recoat as needed. For added slip resistance Glaze’ N Seal Grip ‘n Seal Slip Resistance Additive may be added to the second coat of sealer.
Coverage: 75 to 150 square feet per gallon depending on porosity of surface and method of application.

Limitations: Apply in temperatures between 45°F and 90°F. Air and surface temperature should be above 45oF for 24 hours before and after sealing. Clean up applicators with water immediately after use. Do not apply this sealer to areas where sealer will be immersed such as fountains, pools or below grade areas. Do not use on porcelain, polished stone, granite or marble. For professional use only.
WARRANTY: Glaze ‘N Seal product liability, either expressed or implied, is limited solely to the replacement of this product when proven to be defective and does not include any labor costs or consequential damages. It is the user’s responsibility to determine the safety, toxicity and suitability of this product.

VOC is <100 grams per liter. Complies with SCAQMD regulations.
ADVANCED PAVER CARE PRODUCT LINE
“Natural Look” Paver Sealer is part of Glaze ‘N Seal’s Advanced Paver Care line of products to protect, maintain, and restore. This state-of-the-art product line includes enhancer sealers and restoration products. All products are safe, effective and easy to use
Brand:Glaze 'N SealSKU:914Tags:SealersSize:Gallon (Case of 6), 5 Gallon